Xomo Gt Laser 255 User Manual

The brains of laser cutters and CNC machines, G-code controllers, have a host of settings covering speed, physical limits, directions and intensity (of a laser beam, or rotational speed of a spinning endmill). Even if you’ve bought a pre-made laser or CNC machine, you’re still likely to benefit from fine-tuning the settings for your materials or needs. And if you’re building your own laser or CNC, you’ll need to be all over controller settings.

Misplace your manual? Trying to do some in-depth comparison? We've got you covered! Listed below are links to the owners manuals, user guides, and/or spec sheets for many radar detector models. If you are looking for a description on one particular feature, our feature guide may be of more use. All documents will open in a new window. Oct 21, 2017 1 x User Manual; XOMO GT Laser 255S Mod. The XOMO 150W GT Laser 255S measures 90mm. 60mm. 31mm, which is made of Piano paint processing appearance, 304 Stainless Steel. Comes with built-in battery of 3500mAh, the maximum output is up to 150W.

The best case scenario is that you can adjust the settings you need in a nice user interface, without learning manual configuration via a G-code sender. An example is shown in the image below, from Lightburn software, where the Laser mode enable can be set by clicking a checkbox. Checking the box actually sends settings to your controller in the background, user friendly right ?

So why don’t all machine settings just get shown in a nice user interface ? Well, there’s quite a few settings, and not all of them are relevant to each application and every user, so designers only make interfaces for the minimum. If you need to change a setting that’s not in the user interface, you’ll need to use the command line to send $ settings to your controller.

G-code controllers normally just receive movement directions, such as go to x position 150 at full speed is G0 X150 (note there is no F or feed rate parm, it assumes the fastest feed rate e.g. the $110 value. Reduce $110 if this is too fast). So the $ symbol indicates to the controller that the instructions relate to settings, and are not an instruction to move, burn or cut anything. The command line is circled and highlighted in the image below. It’s where you can click in the space and type in settings (or even directions such as G0 X150 directly).

Instructions

The command-line is available in any G-code sender software.

Useful $ settings

The $$ command reads all your machine’s current settings. It’s a great idea to get started by typing $$ and copying and pasting the results to a backup document, so you can always go back to your existing configuration if you need to. Now you’re ready to make changes !

Our experience with K40 laser is that $100=157 and $101=157 are sweet spots for x and y step distance. Why not try these out ? Try to cut or engrave a 100 x 100 mm square and measure it’s dimensions.

Xomo gt laser 255 user manuals pdf

Another good K40 setting is to increase maximum speed. Experiment around with $110=12000 for x axis $111=5000 or higher for Y axis. 5000 in this case means 5000mm/minute, which is equivalent to 0.08 metres per second. At some point the machine can’t keep up with the signals it receives from the controller, and it’ll skip steps if you go too high. But a higher value that doesn’t skip steps means you’ll get more speed from your machine. Note: x axis rate is higher than y axis rate because of the k40 gantry design.

If you’re building your own DIY machine, must-have $ settings are the steps/mm ($100 for X axis,101 for Y axis), the travelling direction $3 (inverts the direction: 1 is for X, 2 is for only Y and 3 is for both X and Y) and the acceleration $120 and $121 for x and y axis. Safe acceleration settings are around 3000 and 5000 mark.

Back to lasering – another import setting is $30, which is the power range of the laser. When your laser engraves too darkly, increase the $30 from 1000 to a higher number like 1200 etc. Trial and error probably gives you the best setting. When your engraving is too light then simply reduce your $30 setting.

Once again, if you have user-friendly software like Lightburn, many of these settings are in the user interface. It’s just good to know that you can access all settings manually in any G-code sender software if you want to.

Defaults for the Mini Gerbil

Default factory settings
Grbl 1.1f [‘$’ for help]
client> $$
$0=10 (Step pulse time, microseconds)
$1=255 (Step idle delay, milliseconds)
$2=0 (Step pulse invert, mask)
$3=1 (Step direction invert, mask)
$4=0 (Invert step enable pin, Boolean)
$5=1 (Invert limit pins, Boolean)
$6=0 (Invert probe pin, Boolean)
$7=0 (ATC M6, pulse/ff , just for CNC )
$8=100 (ATC Tool Td, milliseconds just for CNC )
$9=100 (ATC M6 Td, milliseconds, just for CNC)
$10=1 (Status report options, mask, used to be 31 to show all info but Lightburn is not happy with other values)
$11=0.010 (Junction deviation, millimeters)
$12=0.002 (Arc tolerance, millimeters)
$13=0 (Report in inches, Boolean)
$19=0 (Softstart, milliseconds, just for CNC spindles)
$20=0 (Soft limits enable, Boolean)
$21=0 (Hard limits enable, Boolean)
$22=1 (Homing cycle enable, Boolean)
$23=3 (Homing direction invert, mask)
$24=2000.000 (Homing locate feed rate, mm/min)
$25=600.000 (Homing search seek rate, mm/min)
$26=250 (Homing switch debounce delay, milliseconds)
$27=4.0 for mechanical or 2.500 for electronic switches (Homing switch pull-off distance, millimeters)
$28=5 (Spindle freq. 0 to 15) – 5 = 1.5kHz
$30=1000 (Maximum spindle speed, RPM)
$31=1 (Minimum spindle speed, RPM)
$32=1 (Laser-mode enable, boolean)
$100=157.000 (X-axis travel resolution, step/mm)
(x:stp/mm)
$101=157.000 (Y-axis travel resolution, step/mm)
(y:stp/mm)
$102=160.000 (Z-axis travel resolution, step/mm)
(z:stp/mm)
$103=160.000 (a:stp/mm)
$104=160.000 (b:stp/mm)
$110=12000.000 (X-axis maximum rate, mm/min equals 200mm/sec)
(x:mm/min) (reduce this if default travel or G0 X0 Y0 is too fast)
$111=5000.000 (Y-axis maximum rate, mm/min)
(y:mm/min)
$112=5000.000 (Z-axis maximum rate, mm/min)
(z:mm/min)
$113=5000.000 (a:mm/min)
$114=5000.000 (b:mm/min)
$120=8000.000 (X-axis acceleration, mm/sec^2)
(x:mm/s^2)
$121=3000.000 (Y-axis acceleration, mm/sec^2)
(y:mm/s^2)
$122=3000.000 (Z-axis acceleration, mm/sec^2)
(z:mm/s^2)
$123=3000.000 (a:mm/s^2)
$124=3000.000 (b:mm/s^2)
$130=320.000 (X-axis maximum travel, millimeters)
(x:mm max)
$131=230.000 (Y-axis maximum travel, millimeters)
(y:mm max)
$132=200.000 (Z-axis maximum travel, millimeters)
(z:mm max)
$133=200.000 (a:mm max)
$134=200.000 (b:mm max)

You can look up G-code reference websites to see settings for potential tweaking.

Electronic limits do work with smaller pull off distances (2.5mm)

Xomo Gt Laser 255 User Manual

If X axis 200mm/sec is too slow you can tweak the speed to higher values. Y axis is usually way slower than the X axis due to the gantry design. Engraving happens across the high speed X axis while the Y axis just do small step increments per engraved line. So tweaking the Y axis does little to increase the engraving process. The default X and Y axis feed rates ($110 and 111) are very conservative values to cater for a big audience of users. Tweaking involves tuning the belt tension as well!

Xomo Gt Laser 255 User Manual 2017

NOTE: $10 needs to be set to 1 (default used to be 31 but it seems not to be supported in LightBurn anymore)

Xomo Gt Laser 255 User Manual Download

Enjoy experimenting, and if you have not used LightBurn why not download a trial version to use with your Mini Gerbil G-code controller for lasers. You don’t have a Mini Gerbil? Okay head over to our purchase page…

Comments are closed.